JoyOne factory · material calculator

Gravel Calculator: How Much Gravel, Mulch or Soil Do You Need?

Measure the ground, pick the material, and the answer comes back in the four units a supplier actually quotes: cubic feet, cubic yards, short tons and bags.

Any shape Multi-area Density with a source Printable shopping list

Material calculator

Material
Gravel and stone
Sand
Soil
Mulch
Aquarium
Area 1 · Rectangle

Beds, lawns, parking pads — anything with square corners.

1.11 cubic yards to buy 30 cu ft · 1.2 short tons · 60 bags of 0.5 cu ft
+46
Volume
30 ft³
Cubic yards
1.11 yd³
Cubic metres
0.85 m³
Weight
2,400 lb
Short tons
1.2
Metric tonnes
1.09 t

120 ft² of ground × 3 in average depth ÷ 12 = 30 ft³

30 ft³ × 80 lb/ft³ (Pea gravel) = 2,400 lb

1.11 yd³ to buy, 60 bags

Type a price above to see a material total.

Bulk density 80 lb/ft³, published range 75–85. Wet material weighs more; your supplier's figure wins.

Area by area (1)
#ShapeMeasurementsDepthAreaVolume
1 Rectangle 12 × 10 ft 3 in 120 ft² 30 ft³

Worked examples

Every number below is produced by the same engine that runs in the browser, at build time — so the examples cannot drift from the calculator above.

Three worked examples — computed by this page's engine at build time
ScenarioMaterialVolumeCubic yardsShort tonsMetric tonnesBags
12 × 10 ft bed, 3 in of pea gravel Pea gravel 30 ft³ 1.11 yd³ 1.2 1.09 60 bags of 0.5 cu ft
20 × 4 ft path, 2 in of #57 stone #57 crushed stone 13.33 ft³ 0.49 yd³ 0.6 0.54 27 bags of 0.5 cu ft
36 in ring around an 8 in trunk, 2 in of bark mulch Bark mulch 1.12 ft³ 0.04 yd³ 0.01 0.01 1 bags of 2 cu ft

Reference tables

Bulk density, with the derived weight of a cubic yard and a cubic metre
Materiallb/ft³short ton/yd³t/m³Source
Pea gravel 75–85 1.01–1.15 1.2–1.36 Engineering ToolBox, bulk densities of common products
#57 crushed stone 85–95 1.15–1.28 1.36–1.52 Engineering ToolBox, bulk densities of common products
#3 crushed stone 85–95 1.15–1.28 1.36–1.52 Engineering ToolBox, bulk densities of common products
#411 crushed stone 85–95 1.15–1.28 1.36–1.52 Engineering ToolBox, bulk densities of common products
River rock 75–85 1.01–1.15 1.2–1.36 Engineering ToolBox, bulk densities of common products
Sand 80–100 1.08–1.35 1.28–1.6 Engineering ToolBox, bulk densities of common products
Topsoil 70–80 0.95–1.08 1.12–1.28 Engineering ToolBox, soil / earth weight
Bark mulch 10–20 0.14–0.27 0.16–0.32 Engineering ToolBox, bulk densities of common products
Wood mulch (non-CCA) 10–20 0.14–0.27 0.16–0.32 Engineering ToolBox, bulk densities of common products
Wood chips 20–30 0.27–0.41 0.32–0.48 Engineering ToolBox, bulk densities of common products
Rubber mulch 25–50 0.34–0.68 0.4–0.8 Engineering ToolBox, bulk densities of common products
Aquarium gravel 75–108 1.01–1.46 1.2–1.73 Engineering ToolBox, bulk densities of common products

How the answer is worked out

Every number on this page comes from area × depth. The shape picker turns your measurements into square feet, the depth box is in inches and is divided by 12, and the two multiply into cubic feet. Cubic yards are cubic feet divided by 27. That is the whole conversion, and it is worth knowing by heart, because bulk material is almost always sold by the cubic yard.

Weight comes from a bulk density: pounds per cubic foot. Pea gravel in the table below sits at 80 lb/ft³, so one cubic yard of it weighs 80 × 27 = 2,160 lb, or 1.08 short tons. If your supplier quotes 1.3 tons for the same yard, nothing is wrong with either number: their stock is wetter, or it is a different stone, or they are quoting a packed volume. The density field is editable for exactly that reason.

Because the engine is deterministic and the same code renders the first paint and every keystroke afterwards, the number you see when the page loads is the number the arithmetic gives — not a placeholder waiting for JavaScript.

What depth should you use?

Depth is the number people guess, and it moves the answer more than anything else: double the depth and you double the order. For mulch, University of Maryland Extension keeps bark mulch between 1 and 3 inches, and keeps gravel or stone used as a topdressing to a 1-inch layer. Those two figures are the ones the material depth menu quotes.

A driveway is a different problem. Layer thickness there depends on your soil, the drainage and what drives on it, and there is no national specification for a private drive to point at. The driveway page therefore starts at 4 inches per lift and tells you to confirm that number with your contractor instead of treating it as code. A playground is the opposite case: the depths there are printed in the CPSC handbook, and the playground page uses them verbatim.

Starting depths, and where each one comes from

Cubic yards, short tons, metric tonnes and bags

Suppliers quote in whatever unit makes their paperwork easy, so the result card shows all of them at once. Three unit traps account for most of the arguments that happen at a material yard.

The first is the ton. A short ton is 2,000 lb; a metric tonne is 1,000 kg, or about 2,204.6 lb. They differ by roughly 10%, which on ten tons is a tonne of free material in one direction or the other. The card labels which one you are reading.

The second is volume against weight for bulk orders. Gravel is sold by the cubic yard because a yard is what a loader bucket measures; the tonnage is a conversion, not a measurement, and it changes with moisture. Mulch is the same: a yard of dry bark and a yard of soaked bark are the same volume and very different weights.

The third is bag size. Bagged mulch is normally 2 cubic feet, sometimes 3; bagged gravel and sand are usually 0.5 cubic feet; rubber mulch and aquarium gravel are bagged by weight, so the bag count depends on the density rather than on the volume. Pick the bag in the form and the count is computed from the same total the bulk figure uses.

Four mistakes that cost a second delivery

The measurements are simple, which is why the errors are boring and repeatable.

What this calculator does not model

It measures the material you spread, not the hole you dig. Compaction of a driveway lift, the depth of a sub-base, a drainage trench, delivery minimums, sales tax and the pallet charge on a bag order are all outside it. It also does not guess a price: the cost field stays empty until you type your supplier's rate, because a market price invented here would be wrong in your state and stale by next month.

Everything runs in the tab. Dimensions are kept in this browser's localStorage so the form remembers them, and a share link puts them in the URL fragment, which browsers do not send to a server. The usage event carries the page, the material and the unit — never a measurement.

Questions this page answers

How many cubic yards is 12 feet by 10 feet at 3 inches deep?

120 square feet × 0.25 feet = 30 cubic feet, and 30 ÷ 27 = 1.11 cubic yards. In the pea gravel on this page that is 2,400 lb, or 1.2 short tons; in #57 stone at 90 lb/ft³ it is 1.35 short tons.

How much does a cubic yard of gravel weigh?

Between about 2,000 and 2,600 lb for the stones in this table, because bulk density runs from 75 to 95 lb/ft³: a yard is 27 ft³, so 75 lb/ft³ gives 2,025 lb and 95 lb/ft³ gives 2,565 lb. Suppliers who quote 1.3 to 1.4 tons per yard are usually describing a wetter or denser material, and their figure beats any table.

Is a ton the same as a cubic yard?

No. A cubic yard is a volume — 27 cubic feet — and a ton is a weight. How many tons a yard weighs depends on the material and how wet it is. This page computes both from the density so you can order in whichever unit the seller uses.

Should I add extra for waste?

Five to ten percent is the usual allowance for cutting, spillage, settling and uneven ground. It matters most for bagged material, where the count is rounded up anyway, and for a driveway, where compaction takes several inches out of the finished lift.

Why is the tonnage different from my supplier's quote?

Bulk density varies with moisture, gradation and how the pile has settled. The table here is a dry, loose reference figure with its published range shown next to it; type your supplier's density into the field and every number recomputes from their figure instead.

Does this work for mulch and topsoil too?

Yes. Mulch, wood chips, topsoil, sand, river rock and rubber mulch are all in the same table, and the mulch calculator page has its own preset. The arithmetic is identical; only the density and the bag sizes change.

Quantity estimate only. Bulk density varies with moisture and gradation, compaction removes depth from a lift, and the depths quoted for playground surfacing come from CPSC Publication 325 for the material and fall height stated there. Check the CPSC handbook and your equipment manufacturer; this calculator does not certify safety. Nothing you type is uploaded.