JoyOne factory · material calculator

Gravel Tons Calculator

The conversion chain, in one place: square feet to cubic feet, cubic feet to cubic yards, cubic yards to short tons and metric tonnes — plus the bag count.

ft³ ↔ yd³ ↔ tonsShort ton vs tonneBags by volume or weightEditable density

Material calculator

Material
Gravel and stone
Sand
Soil
Mulch
Aquarium
Area 1 · Rectangle

Beds, lawns, parking pads — anything with square corners.

1.11 cubic yards to buy 30 cu ft · 1.35 short tons · 60 bags of 0.5 cu ft
+46
Volume
30 ft³
Cubic yards
1.11 yd³
Cubic metres
0.85 m³
Weight
2,700 lb
Short tons
1.35
Metric tonnes
1.22 t

120 ft² of ground × 3 in average depth ÷ 12 = 30 ft³

30 ft³ × 90 lb/ft³ (#57 stone) = 2,700 lb

1.11 yd³ to buy, 60 bags

Type a price above to see a material total.

Bulk density 90 lb/ft³, published range 85–95. Wet material weighs more; your supplier's figure wins.

Area by area (1)
#ShapeMeasurementsDepthAreaVolume
1 Rectangle 12 × 10 ft 3 in 120 ft² 30 ft³

Worked examples

Every number below is produced by the same engine that runs in the browser, at build time — so the examples cannot drift from the calculator above.

The same answer in every unit — computed by this page's engine at build time
ScenarioMaterialVolumeCubic yardsShort tonsMetric tonnesBags
12 × 10 ft at 3 in — #57 stone #57 crushed stone 30 ft³ 1.11 yd³ 1.35 1.22 60 bags of 0.5 cu ft
1 cubic yard by hand — 3 × 3 × 3 ft, 36 in deep #57 crushed stone 27 ft³ 1 yd³ 1.22 1.1 49 bags of 50 lb
10 × 10 ft at 2 in — river rock River rock 16.67 ft³ 0.62 yd³ 0.67 0.6 27 bags of 50 lb

Reference tables

Bulk density, with the derived weight of a cubic yard and a cubic metre
Materiallb/ft³short ton/yd³t/m³Source
Pea gravel 75–85 1.01–1.15 1.2–1.36 Engineering ToolBox, bulk densities of common products
#57 crushed stone 85–95 1.15–1.28 1.36–1.52 Engineering ToolBox, bulk densities of common products
#3 crushed stone 85–95 1.15–1.28 1.36–1.52 Engineering ToolBox, bulk densities of common products
#411 crushed stone 85–95 1.15–1.28 1.36–1.52 Engineering ToolBox, bulk densities of common products
River rock 75–85 1.01–1.15 1.2–1.36 Engineering ToolBox, bulk densities of common products
Sand 80–100 1.08–1.35 1.28–1.6 Engineering ToolBox, bulk densities of common products
Topsoil 70–80 0.95–1.08 1.12–1.28 Engineering ToolBox, soil / earth weight
Bark mulch 10–20 0.14–0.27 0.16–0.32 Engineering ToolBox, bulk densities of common products
Wood mulch (non-CCA) 10–20 0.14–0.27 0.16–0.32 Engineering ToolBox, bulk densities of common products
Wood chips 20–30 0.27–0.41 0.32–0.48 Engineering ToolBox, bulk densities of common products
Rubber mulch 25–50 0.34–0.68 0.4–0.8 Engineering ToolBox, bulk densities of common products
Aquarium gravel 75–108 1.01–1.46 1.2–1.73 Engineering ToolBox, bulk densities of common products

The chain, in order

Length × width gives square feet. Square feet × depth in feet gives cubic feet. Cubic feet ÷ 27 gives cubic yards. Cubic yards × the weight of a cubic yard gives tons. Every one of those steps is exact except the last, and the last is the only one that involves a judgement about the material.

The engine does the chain in that order and prints every intermediate value, so a quote that disagrees with the answer can be traced to the step where the two diverge. Usually it is the density; occasionally it is a supplier quoting a different depth than the one you asked for, or measuring the pile rather than the hole.

Density is the only judgement call

Bulk density is what a cubic foot of the loose material weighs, and it is not a property of the rock itself: the same granite weighs about 168 lb/ft³ as a solid block and 85 to 95 lb/ft³ as crushed stone in a pile, because most of the volume is air. Wet stone is heavier again, because water fills the gaps.

The table behind this page takes its figures from two public reference tables and keeps the published range next to each one. For the crushed stones that range is 85 to 95 lb/ft³, which is 1.15 to 1.28 short tons per cubic yard; for loose gravel it is 75 to 85 lb/ft³, or 1.01 to 1.15 tons per yard. A supplier who quotes 1.3 to 1.4 tons per yard is describing wetter or denser stock, and their number should replace the table's.

The density field accepts any positive number. Type the figure from the supplier's ticket and every output — pounds, tons, tonnes, bags, cost — recomputes from it.

Short tons and metric tonnes are not the same

A short ton is 2,000 pounds and is the default in the United States. A metric tonne is 1,000 kilograms, which is about 2,204.6 pounds, so a tonne is roughly 10% heavier than a short ton. A quote of 10 tonnes is not a quote of 10 tons, and on a driveway-sized order that difference is worth checking before you sign.

The result card shows both, labelled, because a surprising number of stone yards quote in tonnes while their customers read tons. The metric tonne figure is derived through kilograms so it agrees with a metric supplier's own arithmetic.

Bags, when the order is small

Bagged gravel is usually 0.5 cubic feet, and bagged sand the same, while some decorative stone comes in 50 lb bags. A volume bag divides the total volume; a weight bag divides the total weight. Choosing the bag in the form switches which one the count uses, and the count always rounds up.

Two bags of the same nominal size are not always the same amount of material. A 50 lb bag of wet sand holds less volume than a 50 lb bag of dry sand, and a 2 cubic foot bag of mulch holds the same volume whether the bark is soaked or dry but weighs twice as much. That is why the form asks for a bag type rather than just a bag count.

Three checks before you order

First, does the volume match the shape you measured? A circle typed with a radius where the form wants a diameter comes out four times too big, which is the single most expensive typo in this calculator.

Second, does the tonnage land where your supplier expects it? If your 3 cubic yards come out at 3.6 tons and the quarry says 4.2, the difference is density, and their number wins.

Third, is there a delivery minimum? Bulk orders below a few yards are often priced as if they were larger, which is when bags start to make sense. None of that is modelled here; the page gives you the material quantity and lets you price it.

Questions this page answers

How many tons are in a cubic yard of gravel?

Between about 1.01 and 1.28 short tons for the gravels in this table, because bulk density runs from 75 to 95 lb/ft³ and a cubic yard is 27 ft³. Multiply the density by 27 and divide by 2,000 to check any figure.

How do I convert cubic feet to tons?

Multiply cubic feet by the bulk density in lb/ft³ to get pounds, then divide by 2,000 for short tons. For #57 stone at 90 lb/ft³, 30 cubic feet is 2,700 lb, or 1.35 short tons.

Is a tonne the same as a ton?

No. A US short ton is 2,000 lb; a metric tonne is 1,000 kg, about 2,204.6 lb. A tonne is about 10% heavier, so 10 tonnes is roughly 11 short tons.

Why does 1 cubic yard equal 27 cubic feet?

Because a yard is 3 feet in each direction and 3 × 3 × 3 = 27. The conversion is exact, which is why it is the one number in the chain that never needs a range.

Can I use this for sand and topsoil?

Yes — pick them in the material menu. Sand sits at 90 lb/ft³ and loose topsoil at 75 lb/ft³ in the table, with their published ranges shown; wet material will weigh more.

Quantity estimate only. Bulk density varies with moisture and gradation, compaction removes depth from a lift, and the depths quoted for playground surfacing come from CPSC Publication 325 for the material and fall height stated there. Check the CPSC handbook and your equipment manufacturer; this calculator does not certify safety. Nothing you type is uploaded.