JoyOne factory · material calculator

Playground Mulch Calculator

The depths on this page are not suggestions. They are the rows of CPSC Table 2, printed with the fall height each one protects to.

CPSC Table 2Five materialsInitial fill = maintained + 25%Print the sheet

Material calculator

Material
Mulch
Sand
Gravel and stone
Area 1 · Rectangle

Beds, lawns, parking pads — anything with square corners.

13.89 cubic yards to buy 375 cu ft · 4.69 short tons · 188 bags of 2 cu ft
+174
Volume
375 ft³
Cubic yards
13.89 yd³
Cubic metres
10.62 m³
Weight
9,375 lb
Short tons
4.69
Metric tonnes
4.25 t

400 ft² of ground × 9 in average depth ÷ 12 = 300 ft³

300 ft³ × 25 lb/ft³ (Wood chips) = 9,375 lb

+25% waste → 13.89 yd³ to buy, 188 bags

Type a price above to see a material total.

Bulk density 25 lb/ft³, published range 20–30. Wet material weighs more; your supplier's figure wins.

Area by area (1)
#ShapeMeasurementsDepthAreaVolume
1 Rectangle 20 × 20 ft 9 in 400 ft² 300 ft³

Worked examples

Every number below is produced by the same engine that runs in the browser, at build time — so the examples cannot drift from the calculator above.

Table depth, initial fill, and a rubber surface — computed by this page's engine at build time
ScenarioMaterialVolumeCubic yardsShort tonsMetric tonnesBags
20 × 20 ft, 9 in of wood chips (CPSC: 10 ft fall height) Wood chips 300 ft³ 11.11 yd³ 3.75 3.4 150 bags of 2 cu ft
20 × 20 ft, 12 in initial fill for a 9 in maintained depth Wood chips 400 ft³ 14.81 yd³ 5 4.54 200 bags of 2 cu ft
12 × 12 ft, 6 in of shredded rubber (CPSC: 10 ft fall height) Rubber mulch 72 ft³ 2.67 yd³ 1.35 1.22 68 bags of 40 lb

Reference tables

Table 2. Minimum compressed loose-fill surfacing depths — CPSC Public Playground Safety Handbook (Pub. 325), reproduced verbatim
Loose-fill materialInches ofProtects to fall height (ft)
Shredded/recycled rubber * 6 10
Sand 9 4
Pea Gravel 9 5
Wood mulch (non-CCA) 9 7
Wood chips 9 10

* Shredded/recycled rubber loose-fill surfacing does not compress in the same manner as other loose-fill materials. However, care should be taken to maintain a constant depth as displacement may still occur.

The handbook adds: loose-fill materials will compress at least 25% over time, so if a playground requires 9 inches of wood chips the initial fill level should be 12 inches; never use less than 9 inches of loose-fill material except for shredded/recycled rubber (6 inches recommended). Source: cpsc.gov/s3fs-public/325.pdf.

Bulk density, with the derived weight of a cubic yard and a cubic metre
Materiallb/ft³short ton/yd³t/m³Source
Pea gravel 75–85 1.01–1.15 1.2–1.36 Engineering ToolBox, bulk densities of common products
#57 crushed stone 85–95 1.15–1.28 1.36–1.52 Engineering ToolBox, bulk densities of common products
#3 crushed stone 85–95 1.15–1.28 1.36–1.52 Engineering ToolBox, bulk densities of common products
#411 crushed stone 85–95 1.15–1.28 1.36–1.52 Engineering ToolBox, bulk densities of common products
River rock 75–85 1.01–1.15 1.2–1.36 Engineering ToolBox, bulk densities of common products
Sand 80–100 1.08–1.35 1.28–1.6 Engineering ToolBox, bulk densities of common products
Topsoil 70–80 0.95–1.08 1.12–1.28 Engineering ToolBox, soil / earth weight
Bark mulch 10–20 0.14–0.27 0.16–0.32 Engineering ToolBox, bulk densities of common products
Wood mulch (non-CCA) 10–20 0.14–0.27 0.16–0.32 Engineering ToolBox, bulk densities of common products
Wood chips 20–30 0.27–0.41 0.32–0.48 Engineering ToolBox, bulk densities of common products
Rubber mulch 25–50 0.34–0.68 0.4–0.8 Engineering ToolBox, bulk densities of common products
Aquarium gravel 75–108 1.01–1.46 1.2–1.73 Engineering ToolBox, bulk densities of common products

What the handbook actually says

CPSC Publication 325, the Public Playground Safety Handbook, prints a table of minimum compressed loose-fill surfacing depths. It has five rows and two numbers per row: the depth of material and the fall height it protects to. Those ten numbers are reproduced on this page exactly as printed, with the section and table number, and the calculator presets the depth for each material from that row.

The table is a floor for the material and the fall height, not a guarantee. The handbook is explicit that the depths assume a properly maintained layer, that loose fill compresses at least 25% over time, and that the surfacing has to be kept at that depth — which is why it also says to mark equipment supports with a minimum fill level.

Shredded and recycled rubber is the exception in both directions: six inches instead of nine, and a footnote saying it does not compress the same way as the other materials, though displacement still happens.

Compression: order for the depth you want to keep

The handbook's own worked example is the useful one: if a playground needs 9 inches of wood chips, the initial fill should be 12 inches. That is the 25% compression the handbook describes, applied before installation rather than after the first season.

The preset on this page uses a 25% waste allowance for exactly that, and the second example shows the same area calculated at the full 12 inches, so you can see both routes to the same order. Do not skip it: loose fill under a swing loses depth faster than anywhere else on the playground, and the handbook says so.

Compression is also why the maintained depth is the number to check with a ruler, not the number on the delivery ticket. Twelve inches spread is nine inches maintained, and nine inches maintained is what the table row requires.

Maintenance is part of the surface

Loose fill is displaced by feet, by weather and by play. The handbook lists the maintenance obligations plainly: keep the depth at the minimum, pay special attention under swings and at slide exits, and consider wear mats in those areas. A surface that was correct on installation day and never raked since is not the surface the table describes.

The perimeter needs to contain the material — a curb, a timber edge or a trench — or the depth will thin at the edges first. Drainage matters too: standing water compacts the material and reduces its performance, so the surface needs to shed water rather than hold it.

Choosing between the five materials

Wood chips protect to the highest fall height in the table — 10 feet at 9 inches — and are the usual choice where they are locally available and cheap. Wood mulch (non-CCA) protects to 7 feet at the same depth. Pea gravel protects to 5 feet, and sand to 4, which makes both of them a poor fit for equipment with a high platform unless the fall height is genuinely low.

The handbook warns that some loose-fill materials may not meet ADA/ABA accessibility guidance for firmness and stability, and points to ASTM F1951 for testing. Wood products and sand are the usual compromise: they are accessible with effort, and engineered wood fiber is often chosen where accessibility is the priority — but engineered wood fiber is not in this table, because the handbook does not list a depth for it.

Whatever you choose, the equipment manufacturer's instructions govern the surfacing under their equipment, and a local inspector may have a stricter rule than the CPSC minimum.

What this page will not do

It will not tell you that a playground is safe. It converts an area and a depth from the CPSC table into cubic yards, tons and bags. Whether the depth is right for your equipment depends on the fall height of the highest platform, on the equipment's own instructions and on how the surface is maintained. Check the CPSC handbook and your equipment manufacturer; this calculator does not certify safety.

It also does not model a wear mat, a containment curb or a drainage layer — the handbook's own installation figure for loose fill over a hard surface includes a 3-to-6-inch drainage layer of gravel and a geotextile, both of which are separate orders.

Questions this page answers

How deep should playground mulch be?

CPSC Table 2 gives 9 inches of wood mulch (non-CCA) for a 7-foot fall height and 9 inches of wood chips for 10 feet, measured as a compressed, maintained depth. Because loose fill compresses at least 25%, the initial fill for a 9-inch maintained depth is 12 inches.

How much playground mulch do I need?

Area × depth, plus 25% for compression. A 20 × 20 ft area at 9 inches is 300 cubic feet, which is 11.1 cubic yards; adding 25% brings it to 375 cubic feet, or 13.9 cubic yards, about 188 bags of 2 cubic feet.

Is rubber mulch better than wood chips on a playground?

Both protect to 10 feet in the CPSC table, rubber at 6 inches and wood chips at 9. Rubber does not compress the same way and needs less depth, but it is heavier, hotter in sun and does not break down. Follow the equipment manufacturer and your local rules.

Can I use pea gravel under a play set?

CPSC Table 2 lists 9 inches of pea gravel as protecting to 5 feet, which is lower than wood chips and shredded rubber. If your platform is higher than that, pea gravel at 9 inches is not the row you need.

Does this calculator certify my playground as safe?

No. It converts an area and a depth into material quantities. Check the CPSC handbook and your equipment manufacturer; this calculator does not certify safety.

Quantity estimate only. Bulk density varies with moisture and gradation, compaction removes depth from a lift, and the depths quoted for playground surfacing come from CPSC Publication 325 for the material and fall height stated there. Check the CPSC handbook and your equipment manufacturer; this calculator does not certify safety. Nothing you type is uploaded.