JoyOne factory · material calculator
Aquarium Gravel Calculator
Tank length and width, a depth at the front glass and a depth at the back: the slope is what makes a planted tank look right, and it is what most substrate calculators miss.
Material calculator
- Volume
- 0.8 ft³
- Cubic yards
- 0.03 yd³
- Cubic metres
- 0.02 m³
- Weight
- 75 lb
- Short tons
- 0.04
- Metric tonnes
- 0.03 t
4 ft² of ground × 2.5 in average depth ÷ 12 = 0.83 ft³
0.83 ft³ × 90 lb/ft³ (Aquarium gravel) = 75 lb
0.03 yd³ to buy, 15 bags
Type a price above to see a material total.
Bulk density 90 lb/ft³, published range 75–108. Wet material weighs more; your supplier's figure wins.
Area by area (1)
| # | Shape | Measurements | Depth | Area | Volume |
|---|---|---|---|---|---|
| 1 | Rectangle | 48 × 12 in | 2.5 in | 4 ft² | 0.83 ft³ |
Tank panel: a bed that slopes from front to back
The calculator above takes one depth for the whole footprint. Use this panel when the substrate is deeper at the back than at the front: it averages the two depths, measures the tank footprint in inches, and shows the hobby rule of thumb beside the arithmetic so you can see where the two disagree.
- 5 lb bags
- 15
- 20 lb bags
- 4
- Tank capacity
- 44.9 gal
- Footprint
- 4 ft²
Rule of thumb: 1 lb per gallon per inch gives 44.9 gal × 2.5 in = 112 lb, against the 75 lb the footprint gives. The rule assumes a typical tank shape; the footprint figure is the one to buy from.
Worked examples
Every number below is produced by the same engine that runs in the browser, at build time — so the examples cannot drift from the calculator above.
| Scenario | Material | Volume | Cubic yards | Short tons | Metric tonnes | Bags |
|---|---|---|---|---|---|---|
| 48 × 12 in tank, 2 in at the front, 3 in at the back | Aquarium gravel | 0.83 ft³ | 0.03 yd³ | 0.04 | 0.03 | 15 bags of 5 lb |
| 36 × 12 in tank, 1.5 in flat | Aquarium gravel | 0.38 ft³ | 0.01 yd³ | 0.02 | 0.02 | 7 bags of 5 lb |
| 24 × 12 in tank, 2 in flat | Aquarium gravel | 0.33 ft³ | 0.01 yd³ | 0.02 | 0.01 | 6 bags of 5 lb |
Reference tables
Measuring a tank for substrate
Substrate is a volume problem with two measurements: the footprint of the tank and the depth of the bed. Length × width in inches divided by 144 gives square feet; multiply by the average depth in inches and divide by 12 again to get cubic feet. The aquarium form does that arithmetic from the tank dimensions you type.
The depth is where tanks differ from garden beds. Most planted tanks are deeper at the back than at the front, because the slope reads as perspective and because rooted plants need more room at the back. If the front is 2 inches and the back is 3, the average is 2.5, and the volume sits between what a flat 2-inch bed and a flat 3-inch bed would give. Averaging the two ends is exact for a bed whose depth changes linearly from front to back, which is what a straight slope is.
Measure inside the glass, not outside. On a 48-inch tank the difference between inside and outside dimensions is small but it is not nothing, and on a small tank it is proportionally larger.
The "1 lb per gallon per inch" rule
The hobby has a rule of thumb that one pound of gravel per gallon of tank capacity gives one inch of substrate. It is quoted everywhere, it is easy to remember, and it is only approximately true because it silently assumes a typical tank shape. A 10-gallon tank is about 20 × 10 inches, and an inch of gravel over that footprint weighs about 10 lb — which is the rule. A long, shallow tank with the same capacity has a bigger footprint and needs more gravel per inch; a tall, narrow tank needs less.
The calculator shows both numbers: the weight computed from the footprint and the density, and the weight the rule of thumb would predict from tank capacity. When they disagree, the footprint calculation is the one to trust, because it measures the area you are actually covering. The rule is a cross-check, not a specification.
A related habit is worth keeping: rinse new gravel in a bucket until the water runs clear. Dust from the bag will cloud a tank for a day and can clog a filter.
How deep should the bed be?
Two inches is the usual starting point for a tank with plants: deep enough for roots, shallow enough that waste does not disappear into an anaerobic layer. One and a half inches is fine for a bare tank with decorations. Three inches and beyond is for a heavily planted aquascape, and it needs occasional stirring or a substrate that is designed not to compact, because deep beds with no water movement can develop pockets that smell of sulphur when disturbed.
The shape of the bed matters more than the average depth. A slope from 1.5 inches at the front to 3 inches at the back gives plants room and still leaves the front glass visible, which is why the form asks for the two depths separately instead of one number.
Weight, the stand and the glass
Substrate is heavy, and it sits on the bottom glass. A 48 × 12 inch tank with 2.5 inches of gravel at 90 lb/ft³ carries about 75 lb of stone before water, rock or fish. That load is normal for a tank of that size, but it is worth knowing when you are deciding between gravel and a lighter planted substrate.
Distribute the weight: a thin layer of the same gravel across the whole base before you build the slope avoids a point load under the deepest corner. On a rimless tank, check the manufacturer's guidance for substrate depth — some specify a maximum.
Bag sizes and what to buy
Aquarium gravel is sold by weight, usually in 5 lb and 20 lb bags, and sometimes in larger buckets. The calculator counts both bag sizes from the same total, rounded up, so you can see whether 20 lb bags plus a 5 lb bag is cheaper than five 5 lb bags.
Buying a little extra is normal: you will lose some in the rinse bucket and you may want to top up after a rescape. Buying a lot extra is not, because storing gravel is harder than ordering another bag.
Questions this page answers
How many pounds of gravel for a 48 × 12 inch tank with a slope?
At 2 inches at the front and 3 at the back the average depth is 2.5 inches. The footprint is 4 square feet, so the volume is 0.83 cubic feet, which at 90 lb/ft³ is about 75 lb — 15 bags of 5 lb or 4 bags of 20 lb, before rinsing losses.
Is the one pound per gallon rule accurate?
It is a rough cross-check, not a measurement. It assumes a typical tank shape; a long shallow tank needs more per inch and a tall narrow one needs less. Use the footprint calculation and treat the rule as a sanity check.
How deep should aquarium gravel be?
About 2 inches for a planted tank, 1.5 for a plain one, and up to 3 for a deep aquascape. Beyond 3 inches, plan on stirring the bed or using a substrate that resists compaction.
Should I rinse new aquarium gravel?
Yes. Rinse it in a bucket under running water until the water runs clear; the dust in a new bag will cloud the tank and can clog filter media.
Does the slope really change the amount?
It changes it by half the depth difference across the whole footprint. A flat 2-inch bed and a bed that runs 1.5 to 2.5 inches hold exactly the same volume; a 2-to-3 slope holds the same as a flat 2.5-inch bed.
Quantity estimate only. Bulk density varies with moisture and gradation, compaction removes depth from a lift, and the depths quoted for playground surfacing come from CPSC Publication 325 for the material and fall height stated there. Check the CPSC handbook and your equipment manufacturer; this calculator does not certify safety. Nothing you type is uploaded.